Page 1 of 1

Micro-pistols

Posted: Tue Aug 04, 2020 7:09 am
by flcracker
Yes, I know. Too loud. Fireball will burn the hair off your knuckles. Under/overgassed. Unreliable. Insufficient velocity for expansion/fragmentation.

I say: Bring on the boom boom. Use a good muzzle device. Adjustable gas block. Lightweight bolt carrier with short, heavy buffer & spring. Modern bullet construction. And, thirty .22 or .30 caliber holes poked through you will still ruin your day.

I humbly present one of the lightest and shortest AR pistol configurations you can build today, without having to resort to an unobtainium bufferless bolt carrier group.

19" OAL. 4.34# unloaded. Runs like a raped ape.

Itty Bitty Bang-bang

Image

Image

Image

KAK 4.75" barrels (assembled pistol is 5.56, barrel shown is 300BLK). Superlative Arms AGB. Kaw Valley LC (minor milling required to fit AGB screw). Strike Industries 5" pistol buffer tube.

I put well over a hundred rounds of surplus Malaysian 556 FMJ through it last week without a single hiccup. Nice dense pile of brass over my shoulder at about 4:00. Fist-sized group at 25yds - my cheapo RDS was wandering a bit. Time to upgrade to a Holosun.

Itty Bitty Bangbang fits inside a normal sized daypack and has become my new Jeep gun. Consider it as a modern-day Streetsweeper.

Let's see your micro-pistols and hear about the details of your builds.

Re: Micro-pistols

Posted: Tue Aug 04, 2020 10:13 pm
by Big bore lover
Its cute, but I find I must ask,,,,why not simply pickup/buy/use one of the 5.7 pistols out there. Even the high priced FN has 30 round mags and even the cheaper Ruger comes with 20 round mags. No larger than a full size 1911 so it is much easier to "conceal" if needed.

I'm not trying to start anything as to saying the short baby AR is not good. Just asking about a possible alternative.

Re: Micro-pistols

Posted: Wed Aug 05, 2020 6:02 am
by flcracker
If my only goal were to obtain a high-powered compact pistol, then your suggestion would make sense.

At this point I'm my life I have no interest in a new caliber. There's no more room in the ammo dump.

Plus, I like building ARs and dropping coin on a complete firearm just isn't interesting to me right now.

Re: Micro-pistols

Posted: Wed Aug 05, 2020 11:52 am
by rentprop1
I did a 3 inch 9mm AR pistol, its kinda stupid, I just ordered an 8 inch barrel for it, cause at 25 yards its just a bullet hose

Re: Micro-pistols

Posted: Wed Aug 05, 2020 12:18 pm
by NorincoKid
Definitely neat looking, but seems wasteful...how many FPS are you loosing with a barrel that short?

Re: Micro-pistols

Posted: Wed Aug 05, 2020 6:44 pm
by flcracker
I'll find out when all three of the current 300BLK upper projects are assembled. 4.75", 6", and 10". In addition to my current 10.5" that is tuned to run suppressed with a .30cal Windtalker.

Eventually I'd like to build a short & light Form 1 can to try out on these three stubbies.

I realize it's wasteful if the only concern is performance. I already have plenty of rifles and pistols that would be far more preferable in a true SD or SHTF scenario. This is just a lockdown project that will eventually end up in a Pelican case for Jeep/canoe camping/adventure trips.

Re: Micro-pistols

Posted: Wed Aug 05, 2020 7:58 pm
by NorincoKid
Gotcha.

I'm not super knowledgeable about the numbers myself either. I just didn't know if once you got down to that short of a barrel if you were wandering into .22LR ballistics

Re: Micro-pistols

Posted: Sun Aug 09, 2020 12:20 am
by neverenoughguns
Looks like a fun project! Have been kicking around the .300 BO concept for a few weeks. Congrats!