Legality of home made hollowpoints?

Everything ammunition! What to use, where to get it, surplus ammo headstamps, the science of reloading and more.
Casual
Posts: 310
Joined: Fri Jul 20, 2018 1:46 am

Post by Casual »

Uhm we've been pressing a philips bit into .22lr for years :ugeek:
User avatar
joker223
Posts: 89
Joined: Thu Jul 19, 2018 6:51 pm
Location: Seminole County

Post by joker223 »

I once had a "friend" who did this. Accuracy was not too good, performance (expansion) was terrible. This was on a handful of popular calibers.
User avatar
Iosef
Posts: 167
Joined: Sat Jul 21, 2018 8:42 pm

Post by Iosef »

rug357 wrote: Wed Oct 07, 2020 3:59 pm...Bullet makers spend a lot of money to develop their hollow point bullets so it will perform.
Yep, as the British found out back when they were trying to suppress colonial uprisings. Expansion is easily achieved as long as the bullet is traveling faster than 2,000 fps.

At less than 1,000 fps, even the best hollow points tend to expand only half the time. That's one of the reasons we practice the double tap. Of course, you could always handload a .357M or 9mmLugar to over 1,800 fps with the lightest hollow point bullet available, if your pistol can handle the pressure and has a 6" barrrel. I've done this myself in the past for fun. Don't waste your time with plated bullets. The jacket separates at about 1,100 fps.
dammitgriff
Posts: 928
Joined: Tue Jul 31, 2018 11:06 am

Post by dammitgriff »

Jacket separation isn’t necessarily a bad thing when hitting soft targets at typically short engagement distances. Energy is transferred and a nasty wound channel could result in a favorable outcome for the defender.
P5 Guy
Posts: 1299
Joined: Fri Jul 20, 2018 1:20 pm
Location: St Pete

Post by P5 Guy »

Jacket separation in the barrel is a possibility.
Your friend will be taking the covering jacket and turning it into a tube. Remember the back of FMJ is exposed lead, remove the tip and now the jacket MIGHT separate from the lead core. If the jacket stays in the barrel bad things can happen.
Mannlicher
Posts: 42
Joined: Sun Nov 18, 2018 4:39 pm

Post by Mannlicher »

Sometimes a thread is so ridiculous you have to wonder about things. :lol:
TC6969
Posts: 1037
Joined: Wed Jul 18, 2018 2:40 pm
Location: Cocoa

Post by TC6969 »

Mannlicher wrote: Thu Oct 08, 2020 9:01 am Sometimes a thread is so ridiculous you have to wonder about things. :lol:
What?

You mean you don't believe that drilling a bullet will transmit heat through the bullet AND the powder AND the case and somehow still be hot enough to set off a primer? :o
Casual
Posts: 310
Joined: Fri Jul 20, 2018 1:46 am

Post by Casual »

P5 Guy wrote: Thu Oct 08, 2020 7:49 am Jacket separation in the barrel is a possibility.
Your friend will be taking the covering jacket and turning it into a tube. Remember the back of FMJ is exposed lead, remove the tip and now the jacket MIGHT separate from the lead core. If the jacket stays in the barrel bad things can happen.
So use a tmj
TonyR
Moderator
Posts: 460
Joined: Wed Jul 18, 2018 3:57 pm
Location: W.Volusia

Post by TonyR »

Don't be so cheap,buy real hollow points !
Three can keep a secret.......if two are Dead !
User avatar
gforester
Posts: 382
Joined: Thu Jul 19, 2018 12:58 pm
Location: Cocoa, FL and Fort Payne, AL

Post by gforester »

TonyR wrote: Fri Oct 09, 2020 8:25 am Don't be so cheap,buy real hollow points !
Amen! This what I was thinking from the git-go. If you can't afford proper self defense ammo, then you shouldn't be carrying a gun.
Post Reply